Mist Eliminators for Marine Scrubbers: EGCS Compliance
10/30/2026Liquid-Liquid Separation in Polycarbonate Production: Coalescer Internals for Wash Trains and Solvent Recovery
10/30/2026Introduction
In alkylation units, the settler is the critical vessel where the acid catalyst must be separated from the hydrocarbon phase. Whether the process uses hydrofluoric acid (HF) or sulfuric acid (H2SO4), efficient phase separation is essential to avoid acid carryover, maintain alkylate quality, and protect downstream equipment. The internals of the acid settler—coalescer media, plate packs, and distribution plates—play a decisive role in achieving the required separation performance.
This article focuses on the design and function of these internals, with an emphasis on wire mesh coalescers, corrugated plate coalescers, and distribution plates. It provides practical guidance for refinery process engineers involved in the operation, revamp, or troubleshooting of alkylation unit settlers.
Why Upgrade Settler Internals: Lower Acid Loss, Better Separation, Zero Power Cost
Retrofitting an acid settler with properly designed coalescer internals delivers three immediate operational benefits:
- Reduced acid consumption — sharper acid/hydrocarbon interface means less acid carried over with alkylate product, cutting fresh acid make-up rates by 10–30% in typical revamp cases.
- Enhanced acid settling — wire mesh and corrugated plate coalescers agglomerate sub-50 micron acid droplets that gravity settling alone cannot capture, producing drier alkylate and cleaner acid recirculation.
- Static equipment, zero energy cost — mesh pads, plate packs and distribution baffles have no moving parts, no pumps, no instruments and no electricity. They are installed once and operate passively for 3–5 years between turnarounds.
Unlike electrostatic precipitators or electrostatic treaters, which require high-voltage power supplies, regular electrode maintenance and skilled operators, coalescer internals are pure passive mechanical separation — capital cost only, near-zero running cost.
The Problem: Poor Separation Consequences
When acid/hydrocarbon separation in the settler is inadequate, acid droplets become entrained in the hydrocarbon product. In HF alkylation, even small amounts of acid carryover can lead to severe corrosion downstream, catalyst loss, and safety hazards due to the toxic nature of HF. In sulfuric acid alkylation, acid carryover causes corrosion in fractionation and treating sections, and can result in off-spec alkylate due to incomplete reaction or acid-catalyzed side reactions.
Common symptoms of poor separation include:
- High acid content in the alkylate product (measured as acidity or fluoride/sulfate content).
- Emulsion formation and rag layer growth in the settler.
- Fouling of downstream equipment such as exchangers, columns, and reboilers.
- Increased acid consumption and reduced catalyst activity.
- Operational upsets due to level control issues in the settler.
These problems often stem from inadequate coalescer internals, improper distribution, or fouled/damaged internals. Upgrading the settler internals is a proven way to enhance separation efficiency and reduce operating costs.
Wire Mesh Coalescer Internals
Wire mesh coalescers are widely used in acid settlers to promote the agglomeration of fine acid droplets into larger ones that can settle by gravity. The coalescer media typically consists of knitted wire mesh, which provides a high surface area and tortuous paths for droplet capture. Key design parameters include mesh type, material, density, and pad thickness.
Mesh Type and Density: Two common mesh types are plain and reverse (also known as Dutch weave). Plain weave offers a more open structure, while reverse weave provides finer filtration and higher droplet capture efficiency. The mesh density (expressed in kg/m³) influences the coalescing performance; higher density improves capture but increases pressure drop. Typical densities range from 100 to 200 kg/m³, with pad thicknesses from 100 to 300 mm, depending on the acid phase and flow rates.
Materials: For HF service, materials must resist corrosion by HF acid. Monel 400 (UNS N04400) is a standard choice due to its excellent resistance to HF. Hastelloy C276 (UNS N10276) offers superior corrosion resistance and is used in more severe environments. 316L stainless steel may be used in some H2SO4 services but is not suitable for HF. The wire mesh is often constructed from these alloys to ensure long service life.
Function: As the acid/hydrocarbon mixture passes through the wire mesh, acid droplets impinge on the wire surfaces and coalesce. The enlarged droplets then disengage from the mesh and settle to the acid phase at the bottom of the settler. Properly designed wire mesh coalescers can significantly reduce the acid content in the hydrocarbon phase, often to less than 10 ppm in HF service.
Corrugated Plate / Perforated Plate Coalescer
Corrugated plate coalescers (also called plate packs) are used downstream of or in combination with wire mesh coalescers to enhance gravity settling. These internals consist of a series of corrugated plates arranged at an angle, creating narrow channels through which the two-phase mixture flows. The plates are typically made of the same corrosion-resistant alloys as the wire mesh.
Design Parameters: Plate spacing (pitch) typically ranges from 6 to 12 mm, and the plate angle is usually 45° to 60° to facilitate drainage of the coalesced acid. The corrugations create a gentle swirling motion that promotes droplet coalescence and increases the effective settling area. Perforated plates may also be used as distribution or calming baffles, but in the context of coalescers, corrugated plates are more common.
Improved Settling Rate: The plate pack reduces the vertical distance that droplets must travel to reach the acid phase, thereby increasing the settling rate according to Stokes’ law. The inclined plates also provide a surface for droplet coalescence and collection. Compared to gravity settling alone, plate packs can reduce the required settler size or increase throughput for a given vessel.
Distribution Plate (Perforated Baffle)
Proper inlet distribution is critical to the performance of any settler. The incoming mixture must be distributed evenly across the cross-section of the vessel to avoid high-velocity jets, emulsions, and short-circuiting. A distribution plate—often a perforated baffle—is installed at the inlet to break up the flow and create a uniform velocity profile.
Calming Baffles: In addition to the inlet distributor, calming baffles (also perforated plates) may be placed upstream of the coalescer to reduce turbulence and allow initial phase separation. These baffles prevent the incoming stream from disturbing the coalescer media and help in forming a stable interface. The design of perforated plates involves selecting the open area (typically 30-50%), hole size, and spacing to achieve the desired flow distribution with minimal pressure drop.
Typical Internals Arrangement in an Acid Settler
The arrangement of internals in an acid settler follows a logical sequence to maximize separation efficiency. A typical configuration includes:
- Inlet distributor: A perforated baffle or pipe distributor that evenly distributes the incoming mixture.
- Calming baffle: A perforated plate that reduces turbulence and promotes initial separation.
- Wire mesh coalescer: Knitted wire mesh pads that agglomerate fine acid droplets.
- Plate pack: Corrugated plates that enhance gravity settling of larger droplets.
- Outlet: A collector or weir that withdraws the separated hydrocarbon phase, with the acid phase drawn from the bottom.
This arrangement ensures that the mixture is properly distributed, coalesced, and settled before exiting the vessel. The exact configuration may vary depending on the specific process (HF vs. H2SO4), vessel size, and throughput.
Materials of Construction
Material selection is critical due to the corrosive nature of the acids involved. For HF alkylation, Monel 400 is the workhorse material for internals because it resists HF acid attack. Hastelloy C276 is used for more severe conditions or where higher strength is required. 316L stainless steel is generally not recommended for HF service. For sulfuric acid alkylation, 316L stainless steel may be used for dilute acid, but concentrated sulfuric acid requires lead lining or Hastelloy C276. The choice depends on acid concentration, temperature, and presence of impurities.
In H2SO4 service, lead-lined carbon steel is common for the vessel, while internals may be made of Hastelloy C276 or lead-covered steel. It is essential to consult corrosion charts and consider the specific operating conditions when selecting materials.
Maintenance and Inspection Schedule
Regular maintenance and inspection of settler internals are necessary to ensure continued performance. A typical schedule includes:
- Daily: Monitor acid concentration, interface level, and pressure drop across the coalescer (if instrumented).
- Monthly: Check for any changes in product quality (acid content) and inspect for signs of emulsion or rag layer.
- Annual shutdown: Open the settler and inspect internals for fouling, corrosion, and mechanical damage. Clean or replace wire mesh pads and plate packs as needed. Verify distribution plate hole plugging and baffle integrity.
- Every 3-5 years: Perform a thorough inspection of all internals, including non-destructive testing of welds and thickness measurements. Replace corroded components.
Fouling is a common issue, particularly in HF service where acid-soluble oils and polymers can deposit on the mesh. Cleaning may involve solvent washing or replacement of the mesh. Proper pre-treatment of the feed and maintaining acid purity can extend the life of the internals.
Conclusion
Effective acid/hydrocarbon separation in alkylation unit settlers relies on well-designed coalescer internals. Wire mesh coalescers, corrugated plate packs, and distribution plates each play a vital role in agglomerating and separating acid droplets. Proper material selection and maintenance are essential for reliable operation. The result of these upgrades is measurable: lower acid consumption, tighter interface control, and longer run lengths between turnarounds — all from static, passive internals with no added power demand. Influent Separation engineers custom-design these internals for alkylation unit revamps, ensuring optimal performance and longevity. For assistance with your settler internals, contact our team to discuss your specific requirements.
Related Products
- Knitted Wire Mesh Coalescer Media
- Corrugated Plate Separator Media
- Calming Baffles and Perforated Distribution Plates
Frequently Asked Questions
What decides whether a mesh coalescer or a plate pack is used in an acid settler?
How much residence time does an alkylation settler need after the coalescer?
What causes acid carryover into the hydrocarbon phase when the coalescer looks clean?
Does increasing coalescer area always reduce carryover?
How is a coalescer inspected after a shutdown?
- Gas-Liquid Separation Fundamentals — terminology, separation mechanisms and internal selection
- Technical Data Sheet — material and performance reference data
- All Technical Articles — complete engineering index
If you are working on a replacement
A wire mesh pad performs only if it seals to the shell all round, so the measured inside diameter matters as much as the mesh density. See the process data needed to size and select it, what can and cannot be compressed on an urgent replacement and the scope from data review through to delivery.
More on coalescer internals and liquid-liquid separation
- Aftermarket Coalescer Cartridges: Cross-Reference and Replacement Guide – the guide that covers this device family end to end
- Aftermarket Coalescer Cartridges for Produced Water Treatment: OEM-Equivalent
- Hastelloy and Monel Coalescer Internals: Special Alloy Replacement for Corrosive Service
- Cross-Reference Guide: Replacing Major Brand Coalescer Internals
- Produced Water Coalescers for Offshore Platforms: Meeting IMO Oil-in-Water Discharge Limits
Not sure which technology fits the duty at all? Which Mist Eliminator or Coalescer Do You Need? A Selection Map by Duty compares all four on droplet cut point, pressure drop and fouling tolerance.
