What Pressure Drop Should You Expect from a Mist Eliminator?
11/09/2026How to Read a Mist Eliminator Datasheet: The Six Parameters That Decide Performance
11/09/2026A demister floods when the vapor velocity is high enough to hold liquid in the bed instead of letting it drain, and the signature is a sharp rise in pressure drop that tracks flow rather than time. The fix is rarely a new element: check the drainage path first, then the actual operating velocity against the design velocity, then the physical condition of the pad.
Flooding is the most misunderstood failure in mist elimination because the symptoms look like a performance problem — carryover appears, downstream equipment fouls, analyzers drift — while the actual cause is hydraulics inside the pad. Operators respond by asking for a higher efficiency element, which makes the situation worse.
The mechanism in one paragraph
Gas flowing upward through a mesh pad exerts drag on the liquid film held on the wires. At low velocity, gravity wins and liquid drains down and out. As velocity rises, drag rises faster than drainage capacity. At the flooding point the liquid becomes held in the bed, the open area collapses, pressure drop rises steeply, and any additional liquid is pushed out the top with the gas. The captured liquid has become the emitted liquid.
Root causes, ranked by frequency
| Cause | How it presents | How to confirm |
|---|---|---|
| Operation above design velocity | ΔP tracks flow; carryover appears at high load and clears at low load | Recalculate u at current conditions against design u |
| Blocked or undersized drain | Flooding at flows well below the design point | Check drain free area, look for solids or scale in the drain leg |
| Liquid seal in the drain | Pad holds liquid permanently; ΔP high even at low flow | Verify drain terminates in vapor space, not submerged in liquid |
| Gap between pad edge and vessel wall | Local carryover, often asymmetric; downstream fouling on one side | Inspect the perimeter; a gap of a few millimetres is enough |
| Damaged, collapsed or displaced pad | Sudden change after an upset, water hammer or maintenance | Internal inspection; check bed thickness uniformity |
| Excess liquid loading from upstream | Flooding when a tray, nozzle or condenser misbehaves | Trace liquid source; measure liquid rate into the pad |
| Solids or polymer fouling | Progressive rise in ΔP over months, then flooding | Sample the pad, review upstream filtration and wash cycles |
| Poor inlet distribution | Localized flooding with the bulk of the pad still dry | Velocity traverse across the pad face; review inlet device |
Diagnosing it on site in 30 minutes
- Plot ΔP against flow. If the two track together, it is hydraulic. If ΔP rises while flow is flat, it is fouling.
- Compare actual velocity with design. Recalculate with real pressure and temperature, not nameplate values. A gas that is hotter or lighter than design can be well above design velocity at the same mass flow.
- Look at the drain. Confirm the drain leg is clear, correctly sized, and terminates in the vapor space. A drain that ends below the liquid level creates a seal and the pad cannot drain at all.
- Check for a bypass gap. Inspect the pad perimeter. Gas taking a short path around the pad carries liquid straight through.
- Check liquid loading. If the upstream source is producing more liquid than the design case, the pad is being asked to handle a duty it was not sized for.
What actually fixes it
| Root cause | Corrective action | Permanent? |
|---|---|---|
| Velocity above design | Reduce flow, increase pad area, or change to a higher-capacity internal | Yes, if the area or internal is changed |
| Drain blocked or undersized | Clear the drain and resize it for the design liquid rate with margin | Yes |
| Liquid seal | Re-route the drain to terminate in vapor space, or install a proper seal leg with the correct height | Yes |
| Perimeter gap | Install a sealing ring or expandable edge seal | Yes |
| Collapsed pad | Replace the element and check for the upstream cause of the damage | Yes |
| Excess liquid from upstream | Fix the upstream source; add a pre-separation stage such as a vane inlet device | Yes, at the source |
| Fouling | Add or restore washing, upstream filtration, or change to a lower-density mesh | Yes, with a maintenance regime |
| Poor distribution | Install or correct an inlet device; add a flow straightener upstream of the pad | Yes |
The pattern in that table is worth noting: almost every permanent fix is geometric or hydraulic, not “buy a better mesh”. Turning up efficiency by specifying a denser, thicker pad on a vessel that is already velocity limited guarantees earlier flooding.
When to replace instead of repair
Replace the element when the pad geometry has been lost — collapsed, distorted, or compacted — or when fouling has become structural and cannot be washed out. Repair is appropriate when the pad is intact and the cause is external: a blocked drain, a seal, a gap, or an operating condition.
If the vessel is being opened anyway, measure the actual installed geometry: pad diameter, bed thickness, mesh density if it can be identified, and the drainage arrangement. That measurement is what lets a replacement be built to fit without drawings. See our spare parts and replacement elements or urgent replacement service.
Frequently Asked Questions
What causes a demister to flood?
The most common cause is operating above the flooding velocity, where vapor shear holds liquid in the bed instead of letting it drain. Other causes are liquid overload beyond the drainage capacity, a blocked or undersized drain, a liquid seal that stops drainage, damaged or collapsed mesh, and a gap between the pad edge and the vessel wall that lets gas bypass and re-entrain liquid.
How do I tell flooding from fouling?
Flooding appears quickly and is strongly flow dependent: pressure drop jumps when the flow rises and partially recovers when it falls. Fouling develops slowly and is flow independent at first: pressure drop climbs steadily regardless of what the plant is doing. If the trend tracks flow, suspect flooding. If it tracks time, suspect fouling.
Can a demister be repaired if it has flooded?
Flooding itself does not damage the element, so the remedy is usually operational or mechanical rather than replacement: restore the drain path, lower the flow, correct the liquid seal, or close the bypass gap. If the pad has been deformed, collapsed or heavily fouled, replacement is cheaper than attempting to restore geometry.
What is the difference between entrainment and re-entrainment?
Entrainment is liquid carried into the demister from upstream, for example from a tray, a nozzle or a condensation event. Re-entrainment is liquid that the demister had already captured but releases again because it could not drain. Re-entrainment is the failure mode that makes a correctly sized pad perform like an undersized one.
- Gas-Liquid Separation Fundamentals — terminology, separation mechanisms and internal selection
- Technical Data Sheet — material and performance reference data
- All Technical Articles — complete engineering index
If you are working on a replacement
A wire mesh pad performs only if it seals to the shell all round, so the measured inside diameter matters as much as the mesh density. See the process data needed to size and select it, what can and cannot be compressed on an urgent replacement and the scope from data review through to delivery.
More on wire mesh demisters and demister pads
- How Does a Wire Mesh Demister Work? A Complete Guide – the guide that covers this device family end to end
- Demister Sizing: Why Western and Chinese Conventions Give Different Diameters
- Why the Same Demister Duty Gives Different Diameters: Five Conventions That Move the Answer
- Reboiler Mist Eliminators in Ethylene, C3 Splitter Heat Pumps and Refrigeration Chillers
- Why a Shorter Kettle Bundle Can Need a Larger Shell: Length, Diameter and Which Area Binds
Not sure which technology fits the duty at all? Which Mist Eliminator or Coalescer Do You Need? A Selection Map by Duty compares all four on droplet cut point, pressure drop and fouling tolerance.
