Wire Mesh Coalescers for Aromatics Extraction Buffer Settlers

Double-Filament Wire Mesh Coalescer for Hydrogen Peroxide Extraction
10/30/2026
Produced Water Coalescers for Offshore Platforms: Meeting IMO Oil-in-Water Discharge Limits
10/30/2026
Double-Filament Wire Mesh Coalescer for Hydrogen Peroxide Extraction
10/30/2026
Produced Water Coalescers for Offshore Platforms: Meeting IMO Oil-in-Water Discharge Limits
10/30/2026

Introduction

Aromatics extraction units—whether based on sulfolane, N-methyl-2-pyrrolidone (NMP), or tetraethylene glycol (TEG)—rely on efficient liquid-liquid phase separation to recover benzene, toluene, and xylenes (BTX) from reformer or pyrolysis gasoline. In many older units, the settlers and buffer drums that follow the extractor are undersized, and solvent degradation exacerbates emulsion formation. The result: solvent entrainment in raffinate, hydrocarbon carryover in solvent, and significant aromatic yield loss. This article explains how retrofitting knitted wire mesh coalescer internals into existing settlers can debottleneck phase separation without vessel modification.

1. Aromatics Extraction Flow and Settler Function

In a typical BTX extraction unit, feed contacts solvent in an extractor (often a rotating disc contactor or packed column). The extract phase—aromatics plus solvent—leaves the extractor and enters an extract settler, where the rich solvent (heavier phase) separates from the aromatics-rich hydrocarbon phase. The raffinate phase, containing non-aromatics and a small amount of dissolved solvent, proceeds to a raffinate wash section for solvent recovery. Buffer settlers between columns provide residence time for phase disengagement and dampen fluctuations.

Proper separation in these settlers is critical: any solvent carried into the raffinate represents a yield loss and a downstream washing burden, while hydrocarbons entrained in the solvent loop increase energy consumption and contaminate the solvent.

2. Operational Problems in Existing Settlers

Older units frequently face:

  • Solvent entrainment in raffinate: Fine solvent droplets (often <50 µm) remain suspended in the hydrocarbon phase, leading to solvent loss and increased chemical oxygen demand in wastewater.
  • Hydrocarbon carryover in solvent: Aromatics trapped in the solvent phase increase the load on the solvent regeneration section and can degrade solvent quality.
  • Emulsion formation: Degraded solvent (e.g., sulfolane breakdown products) and the presence of fine solids stabilize emulsions, making gravity separation ineffective.

These issues are magnified when the settler is undersized for current throughput or when solvent quality has deteriorated over years of service.

3. How Wire Mesh Coalescers Work

Knitted wire mesh coalescers provide a high-surface-area, tortuous path that promotes droplet agglomeration. As the dispersed phase (e.g., solvent droplets in hydrocarbon) passes through the mesh, droplets impinge on the wire surfaces, coalesce into larger droplets, and rise or settle faster under gravity. The mesh is typically fabricated from SS316L or SS304L wire, knitted into a structured pad with controlled density and thickness.

For aromatics extraction, the mesh pad is installed in the horizontal settler to intercept the dispersion band. The coalescer enhances separation of both the solvent-in-hydrocarbon and hydrocarbon-in-solvent dispersions, depending on placement and orientation.

4. Retrofit Installation Without Vessel Modification

Existing settlers are often empty drums with a single inlet and outlets. Retrofitting a wire mesh coalescer requires no vessel modification: the mesh pad is mounted on a support grid that is inserted through a manway or existing nozzle. The support grid is designed to fit the internal diameter and can be installed during a normal turnaround. The pad is positioned at the bottom of the drum (for solvent-in-hydrocarbon separation) or at the interface level, depending on the specific dispersion.

This approach avoids welding, hot work, and pressure-boundary changes, making it a cost-effective debottlenecking option.

5. Mesh Specifications

Typical mesh density for aromatics settlers ranges from 140 to 220 kg/m³, with a pad thickness of 100 to 150 mm. For difficult emulsions or when fine droplets dominate, a double-layer mesh (coarse layer upstream, fine layer downstream) can be specified to enhance coalescence and drainage. The mesh is often crimped to create a uniform void structure and is edge-sealed to prevent bypass.

6. Performance Improvements

Field experience shows that properly sized wire mesh coalescers can reduce solvent carryover in raffinate by 50–80%, directly improving aromatic recovery and reducing wash water consumption. Hydrocarbon carryover in the solvent loop is similarly reduced, lowering the load on solvent regeneration and improving solvent quality. The result is higher product yield, lower operating cost, and reduced environmental impact.

7. Material Selection

Material choice is critical for corrosion resistance and longevity. SS316L is recommended for sulfolane service due to its resistance to sulfolane degradation products and superior corrosion resistance. SS304 is suitable for less aggressive solvents such as NMP or TEG. Carbon steel is unsuitable because it corrodes and can introduce iron fines that stabilize emulsions, exacerbating separation problems.

Conclusion

Retrofitting wire mesh coalescer internals into existing aromatics extraction settlers and buffer drums is a proven, low-cost debottlenecking strategy. By enhancing droplet coalescence, these internals reduce solvent carryover, improve aromatic recovery, and lower wash water load—all without vessel modification. Influent Separation engineers supply mesh coalescer retrofits for existing aromatics settlers, tailored to your specific solvent, throughput, and vessel geometry. Contact us to discuss your application.

Related Products

Frequently Asked Questions

What is the role of a buffer settler in an aromatics extraction unit?

It gives the coalesced dispersion time to separate after the media stage, so the two phases leave with low cross-contamination. The buffer volume is sized on the coalesced droplet size and on the density difference, and its performance is set by flow distribution at the inlet as much as by its volume.

Why does a buffer settler sometimes perform worse after internals are replaced?

Because the new internals change where the dispersion enters the settling volume. If the outlet of the coalescer is closer to the interface or discharges as a jet, the residence time available is effectively reduced. The internals are correct and the arrangement is wrong, which is why the interface position is checked after any replacement.

How much does temperature variation affect the separation?

It changes viscosity and density difference in opposite directions, so there is usually a temperature at which the settler is least effective. Design at that condition rather than at the nominal one, and check that the interface control can hold through the range the plant actually runs.

What indicates solids accumulation in an aromatics settler?

A rising and unstable interface, a pressure drop increase across the media stage at constant flow, and deposits visible at the media face on inspection. Solids at the interface stabilise the emulsion and cannot be removed by adding coalescer area, so the accumulation has to be dealt with at its source.

Which data is needed to cross-reference a replacement element?

The existing element's measured diameter, height, number of sections, media type and support arrangement, plus the vessel's available height and manway size. A cross-reference built from a part number alone usually produces an element that fits the drawing and not the vessel.

Comments are closed.